tension cylinder Sold to Bangladesh

This article mainly introduces:

Bangladesh hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Bangladesh tension cylinder,produced by Hengyu Group）

tension cylinder are widely used in Bangladesh，because of excellent temperature resistance，clever hydraulic energy conversion，no transmission clearance.So our company has designed tension cylinder for customers from Bangladesh.

Introduction to tension cylinder:

We can not just consider the price and ignore the quality when we purchase the tension cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the tension cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the tension cylinder is not required.

There are some honeycomb holes in the inner wall of the tension cylinder, piston or piston rod surface. How is this formed? When we repair the tension cylinder, we can see that there are some honeycomb holes on the inner wall of the tension cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the tension cylinder is targeted to prevent. Is very necessary.

If the tension cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the tension cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow tension cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the tension cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the tension cylinder includes the leakage caused by excessive wear of the tension cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and tension cylinder, and the phenomenon of "pulling the tension cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When producing oil tension cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

Answers to some questions about tension cylinder:

What are the four cylinders of the truck crane?
The four cylinders of the truck crane generally refer to the telescopic cylinder of the boom (to adjust the length of the boom), the variable amplitude cylinder of the boom (to adjust the elevation Angle of the boom), the horizontal telescopic cylinder of the support leg and the vertical cylinder of the support leg.

How to calculate the tonnage of the hydraulic press without konowing the diameter of the cylinder?
To know the tonnage of the hydraulic cylinder, you first need to know the working pressure of the hydraulic system, the inner diameter of the hydraulic cylinder and the outer diameter of the cylinder rod (the outer diameter of the cylinder rod is needed when calculating the hydraulic cylinder tension). The thrust of the hydraulic cylinder (that is, the force that the hydraulic cylinder can produce by extending out) = the cross-sectional area of the hydraulic cylinder (or the cross-sectional area of the piston) × the working pressure of the cylinder (the cross-sectional area of the piston) =pi*D^2/4= PI (take 3.14) × the square of the cross-sectional area of the piston ÷4 working pressure to see the pressure displayed on the pressure gauge when the maximum load is working.