pressure plate hydraulic cylinder Sold to France

This article mainly introduces:

France hydraulic cylinder,pressure plate hydraulic cylinder manufacturer,pressure plate hydraulic cylinder

(France pressure plate hydraulic cylinder,produced by Hebei Hengyu company）

pressure plate hydraulic cylinder are widely used in France，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed pressure plate hydraulic cylinder for customers from France.

Introduction to pressure plate hydraulic cylinder:

If it is found that the pressure plate hydraulic cylinder lubrication is poor or the pressure plate hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the pressure plate hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the pressure plate hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the pressure plate hydraulic cylinder center line. In this way, when the piston works in the pressure plate hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the pressure plate hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

When the pressure plate hydraulic cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

Improve the service life of the pressure plate hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the pressure plate hydraulic cylinder (such as the pressure plate hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the pressure plate hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the pressure plate hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single pressure plate hydraulic cylinder exhaust.

In the case of serious wear on the inner surface of the pressure plate hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the pressure plate hydraulic cylinder manufacturing process for replacement. The pressure plate hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Answers to some questions about pressure plate hydraulic cylinder:

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.