pusher hydraulic cylinder Sold to Denmark

This article mainly introduces:

Denmark hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

(Denmark pusher hydraulic cylinder,produced by Hebei Hengyu company）

pusher hydraulic cylinder are widely used in Denmark，because of excellent temperature resistance，powerful torque，no transmission clearance.So our company has designed pusher hydraulic cylinder for customers from Denmark.

Introduction to pusher hydraulic cylinder:

If the pusher hydraulic cylinder slips or crawls, please check whether there is astringency inside the pusher hydraulic cylinder, because the internal parts of the pusher hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the pusher hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the pusher hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

pusher hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching pusher hydraulic cylinder block - fine boring pusher hydraulic cylinder block - grinding pusher hydraulic cylinder block. The rolling method is: broaching pusher hydraulic cylinder block - fine boring pusher hydraulic cylinder block - rolling pusher hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the pusher hydraulic cylinder block is about 1-2 days, rolling 1 meter of the pusher hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the pusher hydraulic cylinder increases by 25%. If the pusher hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality pusher hydraulic cylinders, you must take the rolling production process. After the pusher hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

When the pusher hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the pusher hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the pusher hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the pusher hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair pusher hydraulic cylinder are not high.

The method of sleeve pusher hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the pusher hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the pusher hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Answers to some questions about pusher hydraulic cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.