steering cylinder Sold to Turkey

This article mainly introduces:

Turkey hydraulic cylinder,steering cylinder manufacturer,steering cylinder

(Turkey steering cylinder,produced by Hebei Hengyu company）

steering cylinder are widely used in Turkey，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed steering cylinder for customers from Turkey.

Introduction to steering cylinder:

If the steering cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the steering cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow steering cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the steering cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the steering cylinder includes the leakage caused by excessive wear of the steering cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and steering cylinder, and the phenomenon of "pulling the steering cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

If the steering cylinder slips or crawls, please check whether there is astringency inside the steering cylinder, because the internal parts of the steering cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the steering cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

How to repair the steering cylinder body when it is damaged: When the steering cylinder has trace deformation and shallow tensile marks, the steering cylinder is repaired by strong honing process. The heavy honing process can repair steering cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the steering cylinder can meet the technical requirements.

Before the steering cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

Answers to some questions about steering cylinder:

What is the material of the lift cylinder?
The cylinder is composed of many parts. The cylinder also contains the seal and the installation port at both ends, the material of these two parts is not easy to determine if there is no physical object. The cylinder body is generally 20 steel, 45 steel, 27SiMn and other materials, and the piston rod is generally 40Cr, 45 steel and other materials.

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.