High quality hydraulic equipment manufacturers!
        TELL:+8613184968882

        lifter hydraulic cylinder Sold to Argentina

        Release time:2023-11-12 15:28:11 Hits: Current position: Home > News

        This article mainly introduces:

        Argentina hydraulic cylinder,lifter hydraulic cylinder manufacturer,lifter hydraulic cylinder

        Argentina lifter hydraulic cylinder

        (Argentina lifter hydraulic cylinder,produced by Hebei Hengyu company)

        lifter hydraulic cylinder are widely used in Argentina,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed lifter hydraulic cylinder for customers from Argentina.

        Introduction to lifter hydraulic cylinder:

        At the rated pressure, the thrust of the lifter hydraulic cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the lifter hydraulic cylinder is related to the diameter of the lifter hydraulic cylinder, but not to the stroke of the lifter hydraulic cylinder. Moreover, the larger the lifter hydraulic cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the lifter hydraulic cylinder.

        When installing the lifter hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the lifter hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the lifter hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the lifter hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the lifter hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

        When the lifter hydraulic cylinder is in use, ensure that the lifter hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

        The internal leakage of the lifter hydraulic cylinder should be prevented when the lifter hydraulic cylinder is used. The internal leakage of lifter hydraulic cylinder includes the leakage caused by excessive wear of lifter hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

        Answers to some questions about lifter hydraulic cylinder:

        How is the hydraulic cylinder tempered?
        The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

        How to remove the lifting cylinder from the forklift truck?
        The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

        Back to list Recommended article

        Leave a message if you have any questions.

        Send
        Email

        Email:hsslrubbertech@gmail.com7x24 hours

        Glad to receive your consultation!:

        Service
        Tel

        +8613184968882
        7x24hours service

        Add
        Wechat

        Add Wechat
        TOP
        欧美麻豆久久久久久中文| 国产亚洲中文日本不卡二区| 日韩电影无码A不卡| 佐佐木明希一区二区中文字幕| 无码午夜成人1000部免费视频 | 日韩AV片无码一区二区不卡电影| 国产精品午夜福利在线无码 | 免费一区二区无码视频在线播放| 亚洲国产午夜中文字幕精品黄网站 | 日本爆乳j罩杯无码视频| 免费无码专区毛片高潮喷水| 无码精品A∨在线观看免费 | 亚洲精品无码久久久久sm| 中文字幕亚洲男人的天堂网络| 一本一道av中文字幕无码 | 无码中文字幕日韩专区视频| 无码精品人妻一区二区三区漫画 | 佐藤遥希在线播放一二区| 亚洲日韩av无码| 日韩中文久久| 久久伊人亚洲AV无码网站| 中文字幕乱码无码人妻系列蜜桃| 波多野结衣中文字幕久久| a级毛片无码兔费真人久久| 亚洲不卡中文字幕无码| 天堂√在线中文资源网| 亚洲国产精品无码久久九九 | 中文字幕精品一区| 中文字幕免费不卡二区| 色欲香天天综合网无码 | 无码人妻精品一区二区三区久久 | AA区一区二区三无码精片| 亚洲一区AV无码少妇电影☆| 最近免费中文字幕大全免费| 天天看高清无码一区二区三区| 无码内射中文字幕岛国片| 中国无码人妻丰满熟妇啪啪软件 | 中文无码人妻有码人妻中文字幕| 中文精品无码中文字幕无码专区| 免费无码黄十八禁网站在线观看 | 久久精品无码av|