unidirectional cylinder Sold to Kenya

This article mainly introduces:

Kenya hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

(Kenya unidirectional cylinder,produced by Hebei Hengyu company）

unidirectional cylinder are widely used in Kenya，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed unidirectional cylinder for customers from Kenya.

Introduction to unidirectional cylinder:

If the unidirectional cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the unidirectional cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow unidirectional cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the unidirectional cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the unidirectional cylinder includes the leakage caused by excessive wear of the unidirectional cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and unidirectional cylinder, and the phenomenon of "pulling the unidirectional cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

unidirectional cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the unidirectional cylinder is placed for a period of time, the unidirectional cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

When the unidirectional cylinder needs to be stored for a period of time, please follow the recommended methods: The unidirectional cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the unidirectional cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil unidirectional cylinder should not be in direct contact with water vapor for a long time. The unidirectional cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the unidirectional cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the unidirectional cylinder Before working, the unidirectional cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the unidirectional cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The meaning of the unidirectional cylinder model marked by the unidirectional cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the unidirectional cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the unidirectional cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

Answers to some questions about unidirectional cylinder:

How big is a 300-ton cylinder piston?
The rated pressure of the oil pump is 31.5 mpa, the nominal pressure of the hydraulic press is 3150 kN, then the calculated cross-sectional area of the cylinder: S=3150000/31500000=0.1 square meters diameter is: 2* root sign (0.1/3.14) =2*0.178 m =0.356 m 3150 kN hydraulic press is commonly equipped with 31.5 mpa 63 l/min axial piston pump. There are many variable forms of axial piston pump, and the motor size of the pump with the same flow and pressure is not uniform. 31.5 mpa 63 L/min automatic variable pump, can be equipped with 15 kW 4 stage motor; The manual variable pump needs to be equipped with 22 kW 4-stage motor.

Two cylinders have a reversing control, if the load of the two cylinders is not the same, how to ensure their synchronization?
The piston rod of the cylinder is required to extend synchronization: install A shunt collector valve or synchronous motor at port A of the direction control valve, and then connect the two outlets of the shunt collector valve to the rod-free cavity of the two cylinders respectively. It is required that the outlet of the diverter collector valve is connected to the rod cavity of the two cylinders respectively when the piston rod is withdrawn in synchronization. The synchronization performance depends on the quality of the diverter valve and the leakage of the hydraulic system.