forklift cylinder Sold to Czech Republic

This article mainly introduces:

Czech Republic hydraulic cylinder,forklift cylinder manufacturer,forklift cylinder

(Czech Republic forklift cylinder,produced by Hengyu Group）

forklift cylinder are widely used in Czech Republic，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed forklift cylinder for customers from Czech Republic.

Introduction to forklift cylinder:

If air enters the hydraulic system, the forklift cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

When installing the forklift cylinder pipe, the pipe should be cleaned after installation, and should not pass through the forklift cylinder block, and the by-pass pipe must be installed in front of the oil port of the forklift cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the forklift cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the forklift cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

In recent years, the processing process of the forklift cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

When the forklift cylinder needs to be stored for a period of time, please follow the recommended methods: The forklift cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the forklift cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil forklift cylinder should not be in direct contact with water vapor for a long time. The forklift cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the forklift cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the forklift cylinder Before working, the forklift cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the forklift cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about forklift cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

What are the functions of hydraulic cylinders?
Hydraulic cylinder is a hydraulic actuator, the specific role depends on the installation occasion and the type of hydraulic cylinder. Hydraulic cylinder is mainly used in machinery, and it is the most important component of construction machinery. It is important core component which mainly provide power for machinery.