self-locking hydraulic cylinder Sold to Slovakia

This article mainly introduces:

Slovakia hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

(Slovakia self-locking hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

self-locking hydraulic cylinder are widely used in Slovakia，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed self-locking hydraulic cylinder for customers from Slovakia.

Introduction to self-locking hydraulic cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the self-locking hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Improve the service life of the self-locking hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the self-locking hydraulic cylinder (such as the self-locking hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the self-locking hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the self-locking hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single self-locking hydraulic cylinder exhaust.

The assembly work of the self-locking hydraulic cylinder has a great impact on the quality of the self-locking hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The self-locking hydraulic cylinder is not the same as the self-locking hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the self-locking hydraulic cylinder can not be used as a high-power power component, but the self-locking hydraulic cylinder can be used as a relatively large power component, or the self-locking hydraulic cylinder system can be used.

Answers to some questions about self-locking hydraulic cylinder:

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.

Why are the hydraulic cylinders out of sync? The reasons for the unsynchronous operation are as follows: 1, the deviation of the external load of the two cylinders, such as the different resistance and friction of the two cylinders will lead to imbalance. The displacement of the cylinder with low resistance will be larger. 2, the difference in internal friction, such as the difference between the piston and the cylinder of each cylinder, the friction between the piston rod and the seal causes the cylinder to be out of sync. 3. The different resistance of hydraulic oil along the pipeline of the two cylinders causes the cylinder to be out of sync. 4, the deviation of the control original adjustment causes the deviation of the flow to be out of sync, such as the use of an independent throttle valve for each cylinder will appear the difference in the flow of oil in and out of the oil affecting the synchronization of the two cylinders. 5. The cylinder support point of the supported part is initially different.