discharge door cylinder Sold to Indonesia

This article mainly introduces:

Indonesia hydraulic cylinder,discharge door cylinder manufacturer,discharge door cylinder

(Indonesia discharge door cylinder,produced by Hengyu Hydraulic Co., Ltd）

discharge door cylinder are widely used in Indonesia，because of no need for deceleration device，long service life，smooth movement.So our company has designed discharge door cylinder for customers from Indonesia.

Introduction to discharge door cylinder:

When the initial action of the discharge door cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the discharge door cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

When using the discharge door cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the discharge door cylinder block. If the discharge door cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the discharge door cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the discharge door cylinder, so that the working efficiency of the discharge door cylinder is reduced.

When the discharge door cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the discharge door cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

If the discharge door cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the discharge door cylinder. The internal parts of the discharge door cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the discharge door cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the discharge door cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the discharge door cylinder bore processing is out of whack. Because the piston and discharge door cylinder, guide rail and piston rod are relative If the discharge door cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling discharge door cylinder weight composition and calculation. The weight of the discharge door cylinder is composed of the discharge door cylinder diameter, the outer diameter and weight of the discharge door cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Answers to some questions about discharge door cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

What adhesive should be used when the cylinder is cracked?
There is a kind of cast iron glue, industrial products market can buy, A, B formula, that is, a tube is A, a tube is B, when used proportionally prepared, check the instructions. Polish the glue after it dries, and then grind it again.