rolling mill cylinder Sold to Bangladesh

This article mainly introduces:

Bangladesh hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

(Bangladesh rolling mill cylinder,produced by Hengyu Hydraulic Co., Ltd）

rolling mill cylinder are widely used in Bangladesh，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed rolling mill cylinder for customers from Bangladesh.

Introduction to rolling mill cylinder:

rolling mill cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the rolling mill cylinder head itself is the guide sleeve of the piston rod, the rolling mill cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the rolling mill cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the rolling mill cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

When the rolling mill cylinder needs to be stored for a period of time, please follow the recommended methods: The rolling mill cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the rolling mill cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil rolling mill cylinder should not be in direct contact with water vapor for a long time. The rolling mill cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the rolling mill cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the rolling mill cylinder Before working, the rolling mill cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the rolling mill cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

When the rolling mill cylinder is customized, if there are high requirements for the quality of the rolling mill cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the rolling mill cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the rolling mill cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

Answers to some questions about rolling mill cylinder:

Need to buy a hydraulic cylinder, now only know that the pressure needs to be between 20t and 50t. Two-way travel, how to determine the type of cylinder?
Important parameters of the cylinder: cylinder diameter, stroke, use pressure. First, the system pressure must be determined according to the precision of the operation of the application equipment, and the cylinder diameter can be determined by the force and system pressure. Then, according to how the equipment and the cylinder are installed and connected, determine the installation method of the cylinder and then determine the specific installation size, the size of the oil port, whether the buffer is needed and other details.

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.