Release time：2023-11-27 15:08:27 Hits： Current position: Home > News
This article mainly introduces:
Belarus hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder
(Belarus stern plate hydraulic cylinder,produced by Hengyu Group）
stern plate hydraulic cylinder are widely used in Belarus，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from Belarus.
When the initial action of the stern plate hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the stern plate hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.
The method of sleeve stern plate hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the stern plate hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the stern plate hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.
The repair method of the stern plate hydraulic cylinder: the repair of the stern plate hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.
The stern plate hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the stern plate hydraulic cylinder should pay attention to: the operation should be as far away from the stern plate hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the stern plate hydraulic cylinder coating. When cleaning the stern plate hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the stern plate hydraulic cylinder when the oil temperature exceeds 70 ° C.
Two cylinders have a reversing control, if the load of the two cylinders is not the same, how to ensure their synchronization?
The piston rod of the cylinder is required to extend synchronization: install A shunt collector valve or synchronous motor at port A of the direction control valve, and then connect the two outlets of the shunt collector valve to the rod-free cavity of the two cylinders respectively. It is required that the outlet of the diverter collector valve is connected to the rod cavity of the two cylinders respectively when the piston rod is withdrawn in synchronization. The synchronization performance depends on the quality of the diverter valve and the leakage of the hydraulic system.
About the hydraulic cylinder wall thickness problem?
Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.
Add Wechat