hydraulic press cylinder Sold to Germany

This article mainly introduces:

Germany hydraulic cylinder,hydraulic press cylinder manufacturer,hydraulic press cylinder

(Germany hydraulic press cylinder,produced by Hengyu Group）

hydraulic press cylinder are widely used in Germany，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed hydraulic press cylinder for customers from Germany.

Introduction to hydraulic press cylinder:

What kind of process is used in the hydraulic press cylinder to make high-quality hydraulic press cylinder products: the body is the main component of the hydraulic press cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The hydraulic press cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the hydraulic press cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the hydraulic press cylinder increases by 25%. If the service life of the hydraulic press cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. hydraulic press cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic press cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and hydraulic press cylinder are stuck or the hydraulic press cylinder is blocked. At this time, no matter how to manipulate, the hydraulic press cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the hydraulic press cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

hydraulic press cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When the control pressure of the hydraulic system is too low, the hydraulic press cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Disassembly hydraulic press cylinder: When disassembly hydraulic press cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the hydraulic press cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the hydraulic press cylinder.

Answers to some questions about hydraulic press cylinder:

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.