tailboard balance cylinder Sold to Angola

This article mainly introduces:

Angola hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

(Angola tailboard balance cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tailboard balance cylinder are widely used in Angola，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed tailboard balance cylinder for customers from Angola.

Introduction to tailboard balance cylinder:

When the tailboard balance cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the tailboard balance cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

The piston seal of the tailboard balance cylinder is the main element to prevent leakage in the tailboard balance cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

The role of the tailboard balance cylinder in the mold industry: the tailboard balance cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the tailboard balance cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The tailboard balance cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

What kind of process is used in the tailboard balance cylinder to make high-quality tailboard balance cylinder products: the body is the main component of the tailboard balance cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The tailboard balance cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the tailboard balance cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the tailboard balance cylinder increases by 25%. If the service life of the tailboard balance cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. tailboard balance cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the tailboard balance cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and tailboard balance cylinder are stuck or the tailboard balance cylinder is blocked. At this time, no matter how to manipulate, the tailboard balance cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the tailboard balance cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about tailboard balance cylinder:

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

What is the difference between gas-hydraulic pressurized cylinder, pneumatic cylinder and oil cylinder?
The cylinder block is small and the force is large, constant speed and variable speed can be used (easy to change), the adjustment of the output is also convenient, and the freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Easy cylinder control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion.