spring return cylinder Sold to Dominica

This article mainly introduces:

Dominica hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Dominica spring return cylinder,produced by Hengyu Group）

spring return cylinder are widely used in Dominica，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed spring return cylinder for customers from Dominica.

Introduction to spring return cylinder:

The piston rod of the spring return cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

spring return cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a spring return cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' spring return cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the spring return cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The spring return cylinder mainly outputs linear motion and force. The spring return cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston spring return cylinder, plunger spring return cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger spring return cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

When the spring return cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the spring return cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

The body of the spring return cylinder on the processing process requirements: the body of the spring return cylinder is an important and essential part of the spring return cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the spring return cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

Answers to some questions about spring return cylinder:

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

Loader arm fell badly, how to know which oil cylinder is leaking?
No matter which cylinder leakage the arm will drop, it is best to replace the oil seal, even if one cylinder is good, it will not last long, and it will drop the arm, so the two cylinders should be replaced at once.