spring return cylinder Sold to Estonia

This article mainly introduces:

Estonia hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Estonia spring return cylinder,produced by Hengyu Hydraulic Cylinder Factory）

spring return cylinder are widely used in Estonia，because of no need for deceleration device，long service life，smooth movement.So our company has designed spring return cylinder for customers from Estonia.

Introduction to spring return cylinder:

When the long-stroke spring return cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in spring return cylinder head seal damage, oil leakage, and piston sleep in the spring return cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the spring return cylinder; The piston and the piston rod are connected with a spherical joint.

Improve the service life of the spring return cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the spring return cylinder (such as the spring return cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the spring return cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the spring return cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single spring return cylinder exhaust.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the spring return cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The machining accuracy of the spring return cylinder depends on the level of equipment, production technology and testing means. spring return cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

Answers to some questions about spring return cylinder:

How to deal with oil cylinder leakage?
The causes of oil leakage and treatment methods are as follows: (1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear. (2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.

Is it good or bad for the hydraulic cylinder working in the limit stroke position?
It is not good for the hydraulic cylinder working in the limit stroke position. Generally, when the cylinder is used in the limit stroke, the oil in the cylinder will form a backflow back pressure impact on the piston and guide sleeve seals. If the limit is not accurate, it is easy to cause collision damage. It is recommended to leave a buffer of ten to twenty centimeters.