stern plate hydraulic cylinder Sold to Sweden

This article mainly introduces:

Sweden hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

(Sweden stern plate hydraulic cylinder,produced by Hebei Hengyu company）

stern plate hydraulic cylinder are widely used in Sweden，because of excellent temperature resistance，no transmission clearance，simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from Sweden.

Introduction to stern plate hydraulic cylinder:

When the stern plate hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The stern plate hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the stern plate hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil stern plate hydraulic cylinder should not be in direct contact with water vapor for a long time. The stern plate hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the stern plate hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the stern plate hydraulic cylinder Before working, the stern plate hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the stern plate hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

After chrome plating of the piston rod of the stern plate hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the stern plate hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The stern plate hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

Answers to some questions about stern plate hydraulic cylinder:

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.

How to change the seal ring of lift oil cylinder of forklift truck?
Remove the cylinder, put it on the vise, first screw off the big nut plug on the head, and then pull out the guide sleeve, you can directly pull out the core of the cylinder, if it is to change the seal of the cylinder head, the core does not need to be pulled out, if it is to change the seal inside, pull it out and see the oil seal, remove it and replace it, there are three seals of the cylinder head, the inner seal, The outer seal, dustproof, it is best to replace them all together, and be sure to keep them clean when changing, and you can lubricate them with clean hydraulic oil.