accumulator hydraulic cylinder Sold to Vietnam

This article mainly introduces:

Vietnam hydraulic cylinder,accumulator hydraulic cylinder manufacturer,accumulator hydraulic cylinder

(Vietnam accumulator hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

accumulator hydraulic cylinder are widely used in Vietnam，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed accumulator hydraulic cylinder for customers from Vietnam.

Introduction to accumulator hydraulic cylinder:

accumulator hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the accumulator hydraulic cylinder head itself is the guide sleeve of the piston rod, the accumulator hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the accumulator hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

When the control pressure of the hydraulic system is too low, the accumulator hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

When the oil pressure of the accumulator hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

The oil accumulator hydraulic cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about accumulator hydraulic cylinder:

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.