stainless steel cylinder Sold to Costa Rica

This article mainly introduces:

Costa Rica hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Costa Rica stainless steel cylinder,produced by Hengyu Group）

stainless steel cylinder are widely used in Costa Rica，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stainless steel cylinder for customers from Costa Rica.

Introduction to stainless steel cylinder:

After chrome plating of the piston rod of the stainless steel cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The assembly work of the stainless steel cylinder has a great impact on the quality of the stainless steel cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

stainless steel cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

stainless steel cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about stainless steel cylinder:

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.