pressure plate hydraulic cylinder Sold to Belgium

This article mainly introduces:

Belgium hydraulic cylinder,pressure plate hydraulic cylinder manufacturer,pressure plate hydraulic cylinder

(Belgium pressure plate hydraulic cylinder,produced by Hengyu Group）

pressure plate hydraulic cylinder are widely used in Belgium，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed pressure plate hydraulic cylinder for customers from Belgium.

Introduction to pressure plate hydraulic cylinder:

When the pressure plate hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the pressure plate hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the pressure plate hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the pressure plate hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair pressure plate hydraulic cylinder are not high.

The difference between the plunger pressure plate hydraulic cylinder and the piston pressure plate hydraulic cylinder is that the piston in the pressure plate hydraulic cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type pressure plate hydraulic cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

pressure plate hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the pressure plate hydraulic cylinder head itself is the guide sleeve of the piston rod, the pressure plate hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the pressure plate hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

When the hydraulic oil is not pumped into the pressure plate hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the pressure plate hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

Answers to some questions about pressure plate hydraulic cylinder:

How to calculate cylinder speed?
If there is a throttle valve, the cylinder speed will be adjustable. When the throttle is fully opened, the speed of the cylinder reaches the maximum: maximum speed = oil pump displacement ÷ cylinder cavity cross-sectional area The displacement of the oil pump is a main indicator, which can be found on the nameplate, and some can also be known by the oil pump model; The cross-sectional area of the cylinder cavity can be easily calculated. Just make sure the units are the same. And because the cross-sectional area of the rod cavity and the rodless cavity of the cylinder is different, the speed of advance and retreat may also be different.

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.