tilting furnace hydraulic cylinder Sold to Saudi Arabia

This article mainly introduces:

Saudi Arabia hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Saudi Arabia tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tilting furnace hydraulic cylinder are widely used in Saudi Arabia，because of excellent fatigue and impact resistance，excellent temperature resistance，simple structure and reliable operation.So our company has designed tilting furnace hydraulic cylinder for customers from Saudi Arabia.

Introduction to tilting furnace hydraulic cylinder:

When the control pressure of the hydraulic system is too low, the tilting furnace hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

tilting furnace hydraulic cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the tilting furnace hydraulic cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the tilting furnace hydraulic cylinder. c. The tilting furnace hydraulic cylinder seal is extruded, if the O-ring is obviously extruded at the tilting furnace hydraulic cylinder seal, replace the tilting furnace hydraulic cylinder seal.

The internal leakage of the tilting furnace hydraulic cylinder should be prevented when the tilting furnace hydraulic cylinder is used. The internal leakage of tilting furnace hydraulic cylinder includes the leakage caused by excessive wear of tilting furnace hydraulic cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Under normal circumstances, the tilting furnace hydraulic cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the tilting furnace hydraulic cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the tilting furnace hydraulic cylinder and the end cover, the piston and the piston rod, the piston and the tilting furnace hydraulic cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the tilting furnace hydraulic cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

Answers to some questions about tilting furnace hydraulic cylinder:

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.