non-standard special type cylinder Sold to Indonesia

This article mainly introduces:

Indonesia hydraulic cylinder,non-standard special type cylinder manufacturer,non-standard special type cylinder

(Indonesia non-standard special type cylinder,produced by Hengyu Hydraulic Co., Ltd）

non-standard special type cylinder are widely used in Indonesia，because of simple structure and reliable operation，powerful torque，clever hydraulic energy conversion.So our company has designed non-standard special type cylinder for customers from Indonesia.

Introduction to non-standard special type cylinder:

The assembly work of the non-standard special type cylinder has a great impact on the quality of the non-standard special type cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

After chrome plating of the piston rod of the non-standard special type cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The non-standard special type cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the non-standard special type cylinder, bite. Elimination method: When installing the non-standard special type cylinder, ensure that the axis position of the non-standard special type cylinder is consistent with the direction of movement; Make the load borne by the non-standard special type cylinder as far as possible through the non-standard special type cylinder axis, to avoid the phenomenon of eccentricity.

In the process of using the non-standard special type cylinder, sometimes such a problem will occur, the non-standard special type cylinder can not act immediately after the instruction of the non-standard special type cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil non-standard special type cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

Answers to some questions about non-standard special type cylinder:

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.