press hydraulic cylinder Sold to Uzbekistan

This article mainly introduces:

Uzbekistan hydraulic cylinder,press hydraulic cylinder manufacturer,press hydraulic cylinder

(Uzbekistan press hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

press hydraulic cylinder are widely used in Uzbekistan，because of clever hydraulic energy conversion，no transmission clearance，powerful torque.So our company has designed press hydraulic cylinder for customers from Uzbekistan.

Introduction to press hydraulic cylinder:

When the control pressure of the hydraulic system is too low, the press hydraulic cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

press hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching press hydraulic cylinder block - fine boring press hydraulic cylinder block - grinding press hydraulic cylinder block. The rolling method is: broaching press hydraulic cylinder block - fine boring press hydraulic cylinder block - rolling press hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the press hydraulic cylinder block is about 1-2 days, rolling 1 meter of the press hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the press hydraulic cylinder increases by 25%. If the press hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality press hydraulic cylinders, you must take the rolling production process. After the press hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

How to determine the working pressure of the press hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, press hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

In use, the press hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the press hydraulic cylinder.

Answers to some questions about press hydraulic cylinder:

The diameter of the cylinder is 180mm and the pressure is 14mpa. How many tons can the cylinder hold?
Calculate the area of the cylinder, 3.14*9*9=254.34 square centimeters, take the approximate number of engineering, 1 mpa pressure is about 10 kg per square centimeter, 14 mpa pressure is 140 kg per square centimeter, that is 254.34*140=35607.6 kilograms, it can be known that the cylinder can be about 35 tons in theory.

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.