stainless steel cylinder Sold to Portugal

This article mainly introduces:

Portugal hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Portugal stainless steel cylinder,produced by Hengyu Hydraulic Cylinder Factory）

stainless steel cylinder are widely used in Portugal，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed stainless steel cylinder for customers from Portugal.

Introduction to stainless steel cylinder:

stainless steel cylinders in series, parallel and series parallel. Series: In the stainless steel cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the stainless steel cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the stainless steel cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the stainless steel cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

When the stainless steel cylinder is installed, the piston and the stainless steel cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the stainless steel cylinder head boss is easy to cause scars when it hits the inner surface of the stainless steel cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized stainless steel cylinders, only careful and careful operation can be avoided.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the stainless steel cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

stainless steel cylinder is the most important part of construction machinery, the traditional processing method is: broaching stainless steel cylinder block - fine boring stainless steel cylinder block - grinding stainless steel cylinder block. The rolling method is: broaching stainless steel cylinder block - fine boring stainless steel cylinder block - rolling stainless steel cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the stainless steel cylinder block is about 1-2 days, rolling 1 meter of the stainless steel cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stainless steel cylinder increases by 25%. If the stainless steel cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality stainless steel cylinders, you must take the rolling production process. After the stainless steel cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about stainless steel cylinder:

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

What is the main maintenance of the cylinder?
After disassembling the cylinder: 1, clean the cylinder and piston; 2, replace all seals; 3, if there is a valve to repair, to ensure sealing and flexible; 4, deal with all deformation parts; 5. Installation experiment.