shearing machine cylinder Sold to Cameroon

This article mainly introduces:

Cameroon hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

(Cameroon shearing machine cylinder,produced by Hengyu Hydraulic Co., Ltd）

shearing machine cylinder are widely used in Cameroon，because of no need for deceleration device，excellent temperature resistance，no transmission clearance.So our company has designed shearing machine cylinder for customers from Cameroon.

Introduction to shearing machine cylinder:

Piston shearing machine cylinder is widely used in hydraulic transmission. When the shearing machine cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the shearing machine cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the shearing machine cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

When the shearing machine cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the shearing machine cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil shearing machine cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical shearing machine cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the shearing machine cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The repair method of shearing machine cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about shearing machine cylinder:

What is hydraulic cylinder internal leakage and external leakage?
The internal leakage of the hydraulic cylinder refers to the leakage of the piston head seal of the double-acting cylinder, and the leakage occurs inside the cylinder; The external leakage refers to the leakage phenomenon between the cylinder head (or cylinder guide sleeve) and the plunger rod (or piston rod) and the seal between the guide sleeve and the cylinder block, and the oil in the hydraulic cylinder leaks to the outside.

What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.