yg series hydraulic cylinder Sold to UAE

This article mainly introduces:

UAE hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(UAE yg series hydraulic cylinder,produced by Hengyu Group）

yg series hydraulic cylinder are widely used in UAE，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from UAE.

Introduction to yg series hydraulic cylinder:

Improve the service life of the yg series hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the yg series hydraulic cylinder (such as the yg series hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the yg series hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the yg series hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single yg series hydraulic cylinder exhaust.

The scar on the sliding surface of the yg series hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the yg series hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

yg series hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

When the yg series hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the yg series hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil yg series hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical yg series hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the yg series hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Answers to some questions about yg series hydraulic cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.